Futek IHH500 Series Manual do Utilizador

Quick Start GuideSensor Solutions SourceLoad · Torque · Pressure · Multi Component · Calibration · Instruments · Softwarewww.futek.comIHH500Intelligen

10TEDS is a small chip that can store a sensor’s calibration information. The IHH500 can read it upon power up, or by loading it through the menu, and

11To lockout the ability to create, edit, or delete a calibration profile in the IHH500, use the Lock Settings menu.LOCK SETTING MENU1. Menu2. Lock S

12VOLTAGE OUTPUTOutput Type Setup:1. Menu2. Output Config.3. Voltage Config.4. Select Bi-polar or Uni-polarTurn on voltage output:5. Back to exit t

13Bi-polar and Uni-polar for voltage configurations will determine if the output would be ±5VDC for both directional outputs from the sensor, or map bo

14ALARM SETUPAlarm Limit set points:1. Menu2. Sensor Profile3. Edit Channel (Choose appropriate channel)4. Limit & THD5. Alarm Limit Hi and Al

15RELAY SETUPOutput configuration:1. Menu2. Output Config.3. Alarm Relay 1 and Alarm Relay 24. Choose Normally Open or Normally Closed5. Back to Ou

16Data logging is the ability to capture readings over a specified time period for later evaluation. The Data logging information can be uploaded into

17The IHH500 can store up to 21,000 data logging points. Each point is a captured reading.The sampling rate used will be the current sample per second

18The IHH500 can be used with the FUTEK SENSIT software, which can be purchased separately or evaluated through a free trial version available on the

19The IHH500 should be turned on and connected to the computer prior to starting SENSIT.USB output, under Interfaces in the IHH500, should be enabled

2Getting Help0B.01.07-13-0.0 FUTEK reserves the right to modify its design and specifications without notice. Please visit http://www.futek.com/salest

20Performance ReviewINPUTPARAMETER MIN MAX UNITInput Range 1 –500 500 mV/V nom.Input Range 2 –12 12 VDCInput Range 3 0 30 mAOUTPUTPARAMETER MIN MAX UN

21SpecificationsPOWER REQUIREMENT• Power Supply Adapter: 12 VDC/1 A• Internal battery: Rechargeable, lithium polymer battery• Battery size: 7.4V/300

22BANDWIDTHThe digital output bandwidth has been specified as SPS/4.The analog output bandwidth has been specified as SPS/4 for sampling rates less than

23Notes

10 Thomas, Irvine, CA 92618 USATel: (949) 465-0900Fax: (949) 465-0905www.futek.com

3Display FeaturesPowerUSBOutputSensor16×4 Character LCDActive Channel NumberPeak ValueTrackingValley ValueSampling RateBattery IndicatorLarger Font Di

4ButtonsBatteryEnterExitShuntDisplayBackTareGrossResetTrackHoldUnitMenuPowerBatteryEnterExitShuntDisplayBackTareGrossResetTrackHoldUnitMenuPowerBatter

5Connector Pin Configuration6 71 34 5281 42 31 2GMFEDCLBAKJHPowerpage 6USBpage 6Outputpage 6Sensorpage 7

6Wiring LayoutPOWER CONNECTIONSPIN SYMBOL1 12V2 Ground Note: These pins are not polarity sensitive.OUTPUT CONNECTIONSPIN SYMBOL DESCRIPTION1 IDAC anal

7SENSOR CONNECTIONSPIN SYMBOL DESCRIPTIONA +E +ExcitationB +S +SignalC –E –Excitation, TEDS returnD –S –SignalE TEDS_IO TEDS DataF 24_OUT 24V outputPI

8The IHH500 can store up to 15 profiles with channel 2 through 15 being user selectable.1. Menu2. Sensor Profile3. New Channel4. Set channel using l

9The decimal point can be moved by selecting it first and turning it into a number, and then selecting another digit to change it into a decimal point